Internet of Things (IOT) Kit KMS 0202

Internet of Things (IOT) Kit KMS 0202

Internet of Things IOT Starter Kit with Arduino UNO R3

KMS 0202

Exciting IOT Projects included with the new kit

Highlights of the Kit:

• Quick Component Reference book (Hard copy)
• Companion CD with ready to use code
• 15 Exciting IOT projects with step-by-step instructions [e.g., Control Home lights with mobile phone, e-mail alert, Twitter post from Arduino, saving sensor data in SD card etc...]

These projects lay foundation for advanced IOT implementations

Includes:

• With Arduino UNO R3
• W5100 Ethernet Shield (Connect Arduino to Internet / Cloud without PC)
• Temperature Sensor
• Light Sensor
• 4 digit 7 segment display
• Breadboard
• DUPONT Jumper cables x 20
• Relay 5v
• Trim pot 10k
• Transistor 2N2222
• Diode 1N4007
• Resistor 220 ohm x 10
• Resistor 10k x 10
• Red, Green and Yellow LEDs (3 + 3 + 1)
• 9v battery with DC connector
• Network Cable RJ 45
• USB Cable (Type A - B)

Digital Electronics Kit KMS 0301

Digital Electronics Starter Kit

KMS 0301

"Learn Digital Electronics through practice"

PROJECT BOOK INCLUDED (40 Pages)

With 21 hands-on projects to demonstrate logic gates, combination of gates, adders, latches and so on…

Truth table, logic diagram, breadboard wiring diagram and step-by-step instructions!

Packed with:

* 7 digital ICs (4001, 4011, 4069, 4070, 4071, 4077 & 4081)

* 840 hole breadboard

* Push buttons, Resistors, LEDs, Battery, Connectors

* Instruction book with detailed explanation of circuits

Digital Electronic Kit comes bundled with the following:

1. Breadboard x 1
2. 9v battery
3. Battery clip to connect breadboard with battery
4. Jumper wires to connect components within breadboard
5. Pushbutton Switches x 3
6. LEDs 5mm green and red (3 + 3)
7. Resistors 1 MΩ (brown, black, green), 1/4W x 5
8. Resistors 470 Ω (yellow, purple, brown), 1/4W x 5
9. CD4001 DIP IC (4 NOR gates) x 1
10. CD4011 DIP IC (4 NAND gates) x 1
11. CD4069 DIP IC (6 NOT gates) x 1
12. CD4070 DIP IC (4 XOR gates) x 1
13. CD4071 DIP IC (4 OR gates) x 1
14. CD4077 DIP IC (4 XNOR gates) x 1
15. CD4081 DIP IC (4 AND gates) x 1
16. Instruction Book

Internet of Things (IOT) Kit KMS 0201

Internet of Things IOT Starter Kit

KMS 0201

Venture into the world of IOT

Highlights of the Kit:

• Quick Component Reference book (Hard copy)
• Companion CD with ready to use code
• 15 Exciting IOT projects with step-by-step instructions [e.g., Control Home lights with mobile phone, e-mail alert, Twitter post from Arduino, saving sensor data in SD card etc...]

These projects lay foundation for advanced IOT implementations

Includes:

• With Arduino Mega 2560 (More functions compared to Arduino UNO R3)
• W5100 Ethernet Shield (Connect Arduino to Internet / Cloud without PC)
• Temperature Sensor
• Light Sensor
• 4 digit 7 segment display
• Breadboard
• DUPONT Jumper cables x 20
• Relay 5v
• Trim pot 10k
• Transistor 2N2222
• Diode 1N4007
• Resistor 220 ohm x 10
• Resistor 10k x 10
• Red, Green and Yellow LEDs (3 + 3 + 1)
• DC Power Adapter (9v 1A)
• Network Cable RJ 45
• USB Cable (Type A - B)

Digital Clock DIY Kit KMS 0101

Digital Clock Kit

KMS 0101

Make your own digital clock with big display

AT89S52 Microcontroller based digital clock kit

All parts included. Ready to solder. Basic soldering skills required to complete project

Includes:

1. AT89S52 programmed chip.

2. 74HC595 shift registers x 4

3. DS1307 RTC

4. IC base (sockets) for all ICs

5. 7805 voltage regulator with heat sink

6. CR2032 battery with holder

7. 1 inch RED 7 SEGMENT display x 4

8. Red LED x 3, Green LED x1

9. push button x 2

10. 120 ohm and 10 kohm resistors

11. 0.1 uf capacitors (pre-soldered)

12. 22pf capacitors x 2

13. 10 uf capacitor x 2

14. 11.059 MHz and 32.768 KHz crystal

15. 1000uf capacitor

16. 1N4007 diode x 4

17. 4K7 SIP

18. Wires

19. DC Socket

20. Good quality tinned PCB for durability and easy soldering. Includes printed details of where to place components

21. Instructions book on how to solder the components.